Thank you for trusting us with your remote access security needs. We aim to make set-up as easy as possible, but if you experience any difficulties after following the instructions below, please see Troubleshooting below.

This Quick Start Guide describes how to set up your VeeaHub and start using your vTPN Security Service. Each section describes the steps to set up your vTPN service, and then you will be ready to work.

Connecting the Antennas (If you don't have antennas included in the box, skip this step.)
Connect Your VeeaHub to the Internet (DSL, fiber or cable router).
Connect your country-specific adaptor to the power plug and power up. The unit will power up and activate.
Connect Devices to your vTPN Security Service.

Before you start

Go to your confirmation email and find your Wi-Fi connection name (SSID) and password for vTPN.

Your VeeaHub at a glance

What’s in the box?

1 × VeeaHub unit

1 × Power adaptor

5 × Country-specific adaptor plugs

1 × Wall mount bracket with screws

1 × Bluetooth antenna

2 × LTE (cellular) antenna with plugs (VHE09L and VHE10L only)

1 × 100mm x 100mm VESA mounting plate with instructions

1 × Quick Start Guide

For mounting instructions, please see VeeaHub VHE09/VHE10 Mounting Plate Instructions.

VHE09/VHE10 Connections and Lights

Please note

Do not power up your VeeaHub until step 3.
Place or mount your VeeaHub on a flat surface with room (about 3 in/7.5 cm) for air to circulate around it.
If there is a SIM card included with your VeeaHub, it will be visible in the MicroSIM slot (see the diagram). Do not remove or replace the SIM card.
Retain all packaging and materials until after your 30-day trial period is complete.

Connecting the antennas

In the picture, items (1) and (2) are the cellular antennas and item (3) is the Bluetooth antenna. Depending on your model, you may not have these antennas.

Be sure to connect the antennas to the correct connectors, otherwise damage can occur.

Connect your VeeaHub to the Internet

Plug an Ethernet cable into Port 2 (marked “••”) to connect your VeeaHub to the Internet.
Connect the other end of the ethernet cable to your Internet Service Provider's modem or router.

Power up

Insert the plug appropriate for your country into the power adapter. To remove, pull the plug upward while pushing the button.
Plug one end of the power adapter provided into your VeeaHub, and the other end into the outlet. As soon as you plug it in, the VeeaHub will power on. You don’t need to press the Power button.

Activation

The Power light will turn on and the Status light will blink as your VeeaHub is getting started. If you’d like to learn more about the LED lights, click here.

When activation is complete, the two lights will be solid green and the logo on the top of the VeeaHub case will be solid blue.

Activation will complete within 30 minutes.

If activation does not complete, contact the person who ordered your vTPN service. If you ordered directly from Veea, contact us at (+1) 855 488-7332 or https://veea.com/support

Connect devices

After you have activated your VeeaHubs and your mesh setup is complete, you can connect your laptops, printers, phones, and other devices to your VeeaHub.

Check the VeeaHub WiFi name (SSID) and password that was sent in your confirmation email.
Follow the instructions that came with your device to connect it to the VeeaHub WiFi.

Note

To turn off your VeeaHub, briefly press the power button and let go. It will take about 30 seconds before you see all the lights go off.
After that, if the VeeaHub is connected with the power adapter and turned off, press the Power button to power it back on.

Troubleshooting

If you are having problems with your VeeaHub:

Make sure the power adapter is plugged in and the power light is on.
Make sure the Ethernet cable is plugged in and the VeeaHub can connect to the Internet.
Check the status light. If the V-logo light on the top of the unit is not solid blue, it might mean that your VeeaHub is booting up, updating its software, and/or still installing.
Restart your VeeaHub. Unplug from power for 30 seconds and then plug it back in.
If the above steps didn’t resolve the issue, reset your unit by pressing the Reset button for 12 seconds.
If the problem continues, contact the person who ordered your vTPN service. If you ordered directly from Veea, contact us at (+1) 855 488-7332 or veea.com/support